Haier Flat Panel Television 32T51 User Manual

Table of Contents  
Characteristic Functions  
1
2
Important Safety Instructions  
Technical Specifications  
The Technical Specifications for Final Product  
Technical Specifications for TV  
VGA Display Mode  
5
5
6
6
6
6
Power Management  
Packing Listing  
Installation & Connection  
Antenna Connection  
7
7
Power Connection  
8
Computer Connection  
8
HDMI digital port Connection  
AV1 Video Signal Connection  
AV2 Video Signal Connection  
YPbPr/YCbCr Input Connection  
8
9
10  
11  
Position of Control Keys  
Remote Control  
12  
13  
Basic Operation Instruction  
15  
15  
15  
15  
15  
16  
17  
18  
18  
19  
Power On  
Standby  
Signal Source Selection  
Menu Operation Instruction  
PICTURE  
SOUND  
OSD  
ADVANCE  
TV  
Simple Troubleshooting  
22  
 
Important Safety Instructions  
Thank you to choose the LCD TV made by our company, a valuable product with  
excellent quality and multiple functions. This machine will bring you more  
audiovisual enjoyment. Its design can insure user s safety. All machine are strictly  
tested before leaving factory. But incorrect use can lead to electric shock or fire. In  
order to insure safety and extend its life, please read below regulations carefully  
before using it and comply with the following safety instructions.  
When the following troubles occur, please pull out the plug and call the  
professional engineers to repair.  
A. The cable or plug is damaged.  
B. The product was fallen down or the case is  
damaged.  
C. Obvious abnormal situation occurs. In spite  
of correct operation according to the user  
manual but it still can't work normally.  
D. Some abnormal substances or liquid fall into it.  
E. Unusual sound or smell sends out.  
There is high voltage inside the machine but no parts which can be repaired by  
users themselves. In order to assure the people's safety, please do not open  
the case to repair it by yourself. If it is needed to repair, please contact qualified  
engineer to repair.  
Please put this machine in the place of well  
ventilation, instead of extremely hot, cool or  
moist, and direct sunlight.  
The slots on the case is designed to release  
heat so as to assure that all inside components  
will not reach an extra high temperature and  
can work normally for a long time. Please do  
not cover the holes while place it.  
Unless there is good ventilation installation,  
please do not put this machine in inlaid device.  
Please do not place it on an unstable position  
so as to avoid falling off.  
Do not place the LCD TV near water source,  
like a bathtub, pool, washing machine, or moist  
2
 
Important Safety Instructions  
cellar and similar environment.  
During a thunder rain weather, do not touch  
the power cord and antenna cable. Please  
pull out the power line and aerial plugs for  
preventing thunder and lightning damage to  
this machine.  
All cables can be connected or pull out only after power supply is turned off.  
The power cord must be taken off before you  
clean the machine. Do not use the liquid  
cleanser or aerosol cleanser. It is  
recommended to use a wet soft cloth to clean  
the machine. Do not use the alcohol,  
impregnant or ammoniac liquid to wipe the  
screen.  
If you will not use the machine for a long time, please pull out the power cord.  
Do not keep the sleeping mode for too long time.  
Read the manual and marking label before using the machine, and keep the  
user manual for later use.  
Don't use the attachments which are not recommended by the machine  
manufacturer as they may cause hazards.  
The power cord must be placed correctly so as to avoid be trample or crush.  
Please do not make the power socket overloaded or the power cord extended.  
Otherwise it will cause fire or electrical shock.  
The LCD panel is fragile and expensive. The surface of the panel is easy to be  
scratched. Please do not use the hard thing to knock, press, score the panel.  
Otherwise it will be harmful for the panel. The exchange cost is very high.  
All technical specification on this instruction book and outer package are  
subject to change without notice. If the instruction book has slight difference  
with actual operation, please take the actual operation as standard.  
3
 
Important Safety Instructions  
When the MAINS plug or an appliance coupler is used as the disconnect device,  
the disconnect device shall remain readily operable.  
The machine should not suffer from waterdrop  
or watersplash, do not place the vessel with  
water (or other liquids) on it, for like this it is  
possibly to cause fire or electric shock.  
The attaching plug should be inserted into the  
power point completely, otherwise it may cause  
spark to bring fire.  
Please do not put candle, ash-tray, incense, inflammables or explosive nearby  
this machine.  
Please do not stretch into any sharp object, metal or liquid, or touch the signal  
attachment or the inner of radiation hole, in order to avoid short circuit and  
product damage, or possibly causing electric shock. Especially pay attention  
when there are children on the spot.  
Please do not use the machine immediately when moving the machine from low  
temperature place to high temperature one, or install and use at the place of  
facing air conditioning, otherwise it may cause the condensation in the  
machine, to cause fault.  
Must be careful when moving this machine, avoiding being struck, especially  
pay attention to protect the screen part. In addition, if using handcart, must  
note the injury as the product is overturned from the handcart because of hard  
braking, overexerting and uneven ground.  
4
 
Technical Specifications  
The Technical Specifications for Final Product  
Panel size  
26  
32  
Max. Resolution  
Best Resolution  
Pixel Pitch  
1366 768  
1366 768  
1360 768@60Hz  
0.4215mm 0.4215mm  
1360 768@60Hz  
0.51075mm 0.51075mm  
Active Area  
575.770mm 323.710mm 697.6845mm 392.256mm  
Color  
16.7M  
16.7M  
Panel Surface Disposal  
Power Supply  
Anti Glare  
Anti Glare  
100V-240VAC 60/50Hz  
10W+10W  
100V-240VAC 60/50Hz  
10W+10W  
Power Consumption of Speaker  
Control Area of Remote Control  
Operating Environment  
Temperature  
8M 300  
8M 300  
50C ~ 400C  
10%~85%  
50C ~ 400C  
10%~85%  
Humidity  
Atmosphere Pressure  
Storage Environment:  
Temperature  
86kpa-104kpa  
86kpa-104kpa  
-200C ~550C  
5%~95%  
-200C ~550C  
5%~95%  
Humidity  
Atmosphere Pressure  
Dimension (L H W)  
Unpacking: Excluding base  
Including base  
86kpa-104kpa  
86kpa-104kpa  
652 449 104mm  
652 498 104mm  
770 570 200mm  
786 531 110mm  
786 577 110mm  
900 660 220mm  
Packing  
Weight  
10.5Kg  
12.5Kg  
12.5Kg  
16.0Kg  
Net Weight  
Gross Weight  
5
 
Technical Specifications  
Technical Specifications for TV  
1.Supported Systems PAL+SECAM or PAL+NTSC  
2.Storage channels: 199  
3.TV(RF): 75 Imbalance  
4.AV Video-Input: 75 ,1VP-P, RCA  
5.AV Audio-Input: 20K , 500mV RMS  
6.YPbPr/HDMI Video Input: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p  
VGA Display Mode  
No.  
Mode  
Resolution  
720X400  
640X480  
800X600  
1024X768  
1360X768  
Refresh  
70Hz  
1
VGA  
60Hz  
2
3
4
SVGA  
XGA  
60Hz  
60Hz  
WXGA  
60Hz  
Note: Recommended mode:1360X768@60Hz  
Power Management  
This product is complied with EPA Energy Star Standard and compatible with VESA  
DPMS Standard. Details are listed as follows:  
Mode  
On  
LED Indicator  
Off  
Power Consumption  
140W (26")  
170W (32")  
1.5W  
Standby  
Lighting  
Note: All the specifications in the user manual or on the packing carton may be  
changed without additional notice.  
Packing Listing  
1. LCD TV (Excluding base subassembly)  
2. User Manual  
3. Power Cable (or the machine itself has power cable)  
4. Remote Control  
6
 
Installation & Connection  
Antenna Connection  
It is better to use outdoor antenna or CATV cable if you want to watch the colorful and  
hi-definition pictures.  
Attention:  
Please turn off TV power before the outdoor antenna is connected to the TV signal  
input port. Outdoor antenna can't be located near the high voltage cables. Please pull  
out the plug of outdoor antenna to avoid thunder shock in thunder weather.  
7
 
Installation & Connection  
Power Connection  
Notes:  
1.This machine uses AC 100-240V, 60/50Hz.  
2.If a long time at leisure, please disconnect  
it from power supply.  
Computer Connection  
Please connect one end of VGA cord with the output port of the computer (available  
for both desktop or laptop computer),  
and another end of VGA cord with the  
input port of the VGA on its rear cover.  
HDMI digital port Connection  
Connect external HDMI high signal  
source to HDMI digital input port of this  
machine through HDMI digital connector  
cable; push"SOURCE" button to select  
"HDMI" signal source.  
Audio/Video machine with HDMIinterfaces  
8
 
Installation & Connection  
AV1 Video Signal Connection  
Through composite cable, connect AV equipment VIDEO output termination to this  
machine VIDEO input, and AV equipment AUDIO output termination to this machine  
AUDIO input, respectively.  
W
W
R
R
Y
Y
Yellow (VIDEO)  
White (AUDIO-L)  
Red (AUDIO-R)  
W
R
CVBS, DVD Playeror other machine  
with CVBS/S-Video.  
9
 
Installation & Connection  
AV2 Video Signal Connection  
For easy connection to AV Video Signal, there are a group of AV Video Signal input  
ports on the down part on the left side of the machine. The connection method is the  
same as AV1.  
Y
Yellow (VIDEO)  
White (AUDIO-L)  
Red (AUDIO-R)  
W
R
S-VIDEO-2  
AUDIO-R  
R
W
AUDIO-L  
VIDEO-2  
Y
CVBS, DVD Playeror other machine  
with CVBS/S-Video.  
Earphone Socket: The TV speakers will be shut off when earphone is inserted  
into this socket.  
10  
 
Installation & Connection  
YPbPr/YCbCr Input Connection  
If the signal source is DVD, Digital wired receiver or equipments with the  
YPbPr/YCbCr output, recommends you to connect YPbPr or YCbCr output with the  
TV YPbPr/YCbCr input. In order to obtains the better picture quality, at the same  
time, please connect its audio output with TV audio input as shown in the following  
chart. If you choose the YPbPr/YCbCr signal, please set signal source selection  
under YPbPr pattern.  
AV machine  
CVBS, DVD Player or  
other machine with  
YPbPr/YCbCr.  
G
B
Green (Y)  
Blue (Pb/Cb)  
W
R
Y
White(AUDIO-L )  
Red (AUDIO-R, Pr/Cr)  
Yellow (VIDEO)  
W
W
G
B
R
R
R
Y
Download from Www.Somanuals.co1m1. All Manuals Search And Download.  
Position of Control Keys  
Front Panel Control Keys  
SOURCE  
CH+  
3
5
CH-  
VOL+  
VOL-  
6
4
MENU  
7
1
2
1) Power Indicator  
2) Remote Receiving Sensor  
3) SOURCE: Press this key to enter the menu of signal source and choose signal  
source.  
4) MENU: Press this key to enter main menu  
5) CH+/CH-: Press these two keys to select the channel, and adjust the options  
you need under OSD operation.  
6) VOL+/VOL-: Press these two keys to add or reduce volume, and adjust the  
analog value under OSD operation.  
7)  
Power On/Off  
Note: There are some apparent differences between modes, please according to  
practicality.  
12  
 
Remote Control  
POWER  
MUTE  
Power  
Mute  
Numerical key  
F1  
Program list  
Freeze picture  
SMART  
S
SMART  
P
Smart sound  
Smart image  
OK  
OK  
Cursor Key  
Menu  
MENU  
Channel  
Source  
Volume  
VOL  
CH  
SOURCE  
INFO  
16:9  
Info  
Zoom  
Return  
Time  
COLOR  
P/N  
AUDIO  
Color  
Color system  
Telecontrol battery installation method  
Take off the cover of battery box, fix two AAA batteries with 1.5 volt, and conform  
with the polarity of remote control battery box.  
Note: Appearance of the remote control may be different from this picture, please  
according to practicality.  
13  
 
Remote Control  
Remote Control Key Instruction  
Key  
Function  
POWER Turn on or standby  
MUTE Eliminate sound  
Numerical key Number input button  
F1  
Program list  
MENU  
Freeze picture  
Look through or edit Program list  
Press this button to display menu  
SMART S  
SMART P  
SOURCE  
Cursor key  
Intelligent sound mode selection: STANDARD, NEWS, MUSIC, PERSONAL  
Intelligent image mode selection: STANDARD, DYNAMIC, SOFT, PERSONAL  
Press this button to display signal source selection menu  
Up or Down cursor button: function select  
Left or right cursor button: analog add or reduce  
Sound volume add or reduce button  
VOL+/VOL-  
CH+/CH-  
INFO  
Select channel Number  
System information display switch  
Time  
Timer setting button, press this key can set time of turning down.  
15  
OFF  
30  
45 60  
120  
Return  
16:9  
Color  
P/N  
AUDIO  
OK  
Press this button to return to last watching channel  
"FULL", "MOVIE", "CAPTION", "4:3", "PANORAMA"  
Color temperature mode selection button: Normal, Warm, Cool  
Color system mode selection button: PAL, NTSC(SECAM), Auto  
Optional  
Confirm operation  
Precautions for use of remote control:  
1. When using remote control you should point it to the remote-control inductive  
window. The goods between remote control and inductive window may hinder  
normal operation.  
2. Do not cause the remote control to receive fierce vibration. In addition, do not  
set or place the remote control under direct sunlight, for the thermal energy will  
cause the distortion of remote control.  
3. When remote-control inductive window of main machine is under direct sunlight  
or intense illumination, the remote control may malfunction, by now, please  
change the angle of illumination or this machine, or approach the inductive  
window to operate the remote control.  
4. When the battery voltage is insufficiency it influences the remote control  
distance, you should replace with new battery; when not to use the remote  
control for long or the battery is exhausted, please take out the battery, in order  
to avoid bringing the battery leakage to corrode the remote control and thus  
cause it out of commission.  
5. Do not use different batteries. The mix use of new and old batteries is not  
allowed, you should use battery pair.  
6. Do not throw battery into fire, charge or disassembly, especially do not charge,  
assemble and disassemble, heat or burn to the used battery. Please observe the  
related environmental protection stipulation on wasted battery.  
14  
 
Basic Operation Instruction  
Power On  
Plug power cord into the electrical socket and press '' '' key on the front panel, then  
press ''Power'' key on the remote control to turn on the TV.  
Standby  
Press ''Power''key on the remote control. TV will be in standby.  
Special Attention:  
1.TV set will automatically turn to standby if there is no signal input for 5 minutes  
when TV turns on.  
2.TV set will automatically turn to standby when the preset time of turning off  
reaches.  
Signal Source Selection  
Press ''SOURCE'' key either on the remote control or on the  
T V  
AV 1  
AV 2  
S - V I D E O 1  
S - V I D E O 2  
Y P B P R  
H D M I 1  
H D M I 2  
P C  
front panel. ''MENU OF SIGNAL SOURCE'' will be displayed  
on the screen. Then press ''Up/Down'' key on remote control  
or "CH+/CH-" key on the front panel to choose the signal  
source such as TV, AV1, AV2, S-VIDEO1, S-VIDEO2, YPBPR,  
HDMI1, HDMI2, PC, USB. Press ''OK'' key on the remote  
control or ''MENU" key on the front panel and TV will switch  
the current signal source to the signal source you choose.  
U S B  
Menu Operation Instruction  
Press ''MENU'' key on the remote control or on the front panel. The TV will display the  
main menu.  
1. Press ''Left/Right'' key on the remote  
control or ''VOL+/VOL-''key on the front  
P I C T U R E  
panel to select the adjustment sort menu,  
C O N T R A S T  
B R I G H T N E S S  
H U E  
S A T U R AT I O N  
S H A R P N E S S  
P I C T U R E M O D E  
S C A L E  
5 0  
5 0  
5 0  
5 0  
5 0  
which includes 5 sorts: PICTURE, SOUND,  
OSD, ADVANCE, TV.  
2. Press ''Down''key on the remote control  
or ''CH-'' on the front panel to enter the  
adjustment sort menu.  
STANDARD  
FULL  
NORMAL  
MIDDLE  
C O L O R T O N E  
3 D N R  
S E L  
A D J  
M E N U E X I T  
3. Press ''Up/Down'' key on the remote control  
or ''CH+/CH-'' on the front panel to select what is needed to adjust in sort menu.  
4. Press ''Left/Right'' key on the remote control or ''VOL+/ VOL-''on the front panel to  
adjust the value or setting.  
5. Press ''Menu'' key to exit the main menu when the TV displays the Main Menu;  
Press ''Menu'' key to return to previous menu when the TV displays the submenu;  
15  
 
Basic Operation Instruction  
Press ''Source''key to display the signal source menu or exit signal source menu.  
6. During the operation, the selections which can not be adjusted at current mode will  
be hidden automatically and the color of the selections will be changed into gray.  
7. Menu Operation Instruction in this manual is explained according to TV mode. The  
operations in other modes are similar to the one in TV mode. Users can take it as  
reference.  
PICTURE  
Select  
to enter the PICTURE submenu.  
Press "Up/Down" key on the remote control or  
"CH+/CH-" key on the front panel to choose  
what you need. Press the "Left/Right" key on  
the remote control or the "VOL+/VOL-" key  
on the front panel to adjust analog value or  
state (see below table).  
P I C T U R E  
C O N T R A S T  
B R I G H T N E S S  
H U E  
S A T U R AT I O N  
S H A R P N E S S  
5 0  
5 0  
5 0  
5 0  
5 0  
P I C T U R E M O D E  
S C A L E  
STANDARD  
FULL  
C O L O R T O N E  
3 D N R  
NORMAL  
MIDDLE  
Special Attention  
1. The Hue function is available only for  
NTSC system.  
S E L  
A D J  
M E N U E X I T  
2. The value adjusted by user, such as Contrast, Brightness, Saturation, Hue, and  
Sharpness will be saved automatically by the machine as personal mode.  
Remote Control Shortcut Keys  
SMART P: Press SMART P key on the remote control. You can switch the function  
among the "STANDARD", "DYNAMIC", "SOFT", "PERSONAL" four modes .  
16:9: Press 16:9 key on the remote control, you can switch the mode among the  
"FULL", "MOVIE", "CAPTION", "4:3", "PANORAMA" five modes.  
Option  
Description  
Function  
Adjust the contrast of whole  
picture  
Increasing analog value increases Contrast;  
CONTRAST  
Decreasing analog value decreases Contrast(0-100).  
Adjust brightness and blackness Increasing analog value increases brightness;  
BRIGHTNESS  
HUE  
of whole picture  
Decreasing analog value decreases brightness(0-100).  
Increasing analog value increases green;  
Adjust the hue of whole picture  
Decreasing analog value increases purple(0-100).  
Increasing analog value increases color;  
Adjust the saturation of whole  
picture  
SATURATION  
SHARPNESS  
Decreasing analog value decreases color (0-100).  
Increasing analog value increases definition;  
Decreasing analog value decreases definition (0-100).  
Adjust the sharpness of whole  
picture  
PICTURE MODE Select picture mode  
"STANDARD", "DYNAMIC", "SOFT", "PERSONAL" four modes.  
"FULL", "MOVIE", "CAPTION", "4:3", "PANORAMA",  
Select picture scale  
SCALE  
Select color temperature mode  
There are three Color Temperature modes,  
"NORMAL", "WARM", "COOL ".  
COLOR TONE  
3D NR  
of the picture  
Select model of3D NR  
"MIDDLE", "STRONG", "WEAK", "OFF".  
16  
 
Basic Operation Instruction  
SOUND  
Select  
to enter the SOUND submenu.  
Press " Up/Down " key on the remote  
control or the key "CH+/CH-" on the front  
panel to choose what you need. Press the  
"Left / Right" key on the remote control or  
the "VOL+/VOL-" key on the front panel to  
adjust analog value or state (see below  
table).  
SOUND  
B A S S  
T R E B L E  
B A L A N C E  
S O U N D M O D E  
5 0  
5 0  
5 0  
STANDARD  
S E L  
A D J  
M E N U E X I T  
Special Attention  
1. Normally, 50 value of adjustment is  
recommended;  
2. The treble or bass analog value which is adjusted by the users will be saved as  
the personal mode by the machine  
Remote Control Shortcut Keys  
SMART S: Press SMART S key on the remote control. You can switch the function  
among the, "STANDARD","NEWS", "MUSIC", "PERSONAL" four modes.  
MUTE: Open or close sound.  
VOL+/VOL-: Add or reduce volume.  
Option  
Function  
Description  
Increasing analog value increases bass;  
BASS  
Adjust bass value  
Decreasing analog value decreases bass (0-100).  
Increasing analog value increases treble;  
Adjust treblevalue  
TREBLE  
Decreasing analog value decreases treble (0-100).  
Increasing analog value decreasing left volume;  
BALANCE  
Adjust balanceof left orright sound  
Decreasing analog value decreases right volume(0-100).  
SOUND MODE Adjust audio effect mode  
"STANDARD", "NEWS", "MUSIC", "PERSONAL" four modes.  
17  
 
Basic Operation Instruction  
OSD  
Select  
to enter the OSD submenu. Press  
"Up/Down" key on the remote control or  
"CH+/CH-" key on the front panel to choose  
what you need. Press the "Left/Right" key on  
the remote control or the "VOL+/VOL-" key  
on the front panel to adjust analog value or  
state (see below table).  
OSD  
OSD - H POSITION  
OSD - V POSITION  
OSD - DURATION  
OSD - HALFTONE  
OSD - LANGUAGE  
5 0  
5 0  
1 5  
1 0 0  
ENGLISH  
S E L  
A D J  
M E N U E X I T  
Option  
Function  
Description  
Increasing analog value, OSD menu movetoward right;  
OSD-H POSITION Adjust H-position ofOSD menu  
OSD-V POSITION Adjust V-positionof OSD menu  
Decreasing analog value, OSD menu movetoward left (0-100).  
Increasing analog value, OSD menu movetoward down;  
Decreasing analog value, OSD menu movetoward up(0-100).  
OSD-DURATION  
OSD-HALFTONE  
OSD LANGUAGE  
Adjust duration ofOSD menu  
Adjust halftone ofOSD menu  
Choose OSD menudisplay language  
Increasing analog value, extend duration timeof OSD menu;(5-60).  
Increasing analog valueincreases halftone;  
Decreasing analog valuedecreases halftone(0-100).  
There are manylanguages to select  
ADVANCE  
Select  
to enter the ADVANCE submenu.  
Press "Up/Down"key on the remote control  
or "CH+/CH-"key on the front panel to choose  
what you need. Press the "Left/Right" key on  
the remote control or the"VOL+/VOL-" key on  
the front panel to adjust analog value or state  
(see below table).  
ADVANCE  
SLEEP - TIMER  
DCC  
BLUE SCREEN  
RESETTING  
O F F  
O F F  
O N  
S E L  
A D J  
M E N U E X I T  
Option  
Function  
Description  
SLEEP - TIMER  
Set sleep timeof the machine  
"Off, 15M, 30M, 45M, 60M, 120M", unit: minute.  
"ON/OFF", two states.  
DCC  
Open or closeDCC  
Open or closeBLUE SCREEN  
Resume to settingof factory  
"ON/OFF", two states.  
BLUE SCREEN  
RESETTING  
Reset all values to setting of factory.  
18  
 
Basic Operation Instruction  
TV  
Select  
to enter the TV submenu. Press  
"Up/Down" key on the remote control or  
"CH+/CH-" key on the front panel to choose  
what you need. Press the "Left/Right"key on  
the remote control or the "VOL+/VOL-" key  
on the front panel to adjust analog value or  
state (see below table).  
T
V
AUTO  
M
MONO  
OFF  
COLOR SYSTEM  
SOUND SYSTEM  
MTS  
SKIP  
AUTO SCAN  
MANUAL SEARCH  
FINE TUNING  
CHANNEL EDIT  
S E L  
A D J  
M E N U E X I T  
Option  
Function  
Description  
COLOR SYSTEM  
SOUND SYSTEM  
Select color system  
Select sound system  
"PAL, NTSC,AUTO" three modes.  
"I, D/K, M, AUTO, B/G" five modes.  
MTS  
Select MTS modes  
Select skip ornot  
Select auto scan  
Select manul search  
Select fine tuning  
"STEREO, MONO, DUAL , DUAL " four modes.  
"ON/OFF" two states.  
SKIP  
AUTO SCAN  
MANUAL SEARCH  
FINE TUNING  
CHANNEL EDIT  
Please refer to "AUTO SCAN"  
Please refer to "MANUAL SEARCH"  
Please refer to "FINE TUNING"  
Please refer to"CHANNEL EDIT"  
Select channel edit  
AUTO SCAN  
Select  
to enter the submenu of TV. Then  
5 3 . 0 0 MHZ  
CH  
2
press ''Up/Down'' key on the remote control  
or ''CH+/CH-'' on the front panel to select  
''AUTO SCAN''. The machine perform search after pressing ''Right ''key on the  
remote control or ''VOL+''on the front panel. (In the process of searching the channel  
automatically, press the key of ''MENU'' on the remote control to stop searching).  
Meanwhile, it will show Current Channel, Frequency. All of the TV programs will be  
saved automatically.  
MANUAL SEARCH  
CHANNEL  
SEARCH  
2
Select to enter the submenu of TV. Then  
press ''Up/Down'' key on the remote control  
4 5 . 2 5 MHZ  
or ''CH+/ CH-''on the front panel to select ''MANUAL SEARCH''. Then press the key  
of ''Right'' on the remote control or ''VOL+'' on the front panel to enter submenu of  
MANUAL SEARCH. Press ''Left/Right'' key on the remote control or ''VOL+/VOL-'' on  
the front panel to select channel No.. Press ''Up/Down'' key on the remote control to  
select ''SEARCH '', press ''Left/Right'' key on the remote control again, the machine  
begin searching toward low frequency or high frequency. (In the process of searching  
the channel automatically, press the key of ''MENU'' on the remote control to stop  
searching).  
19  
 
Basic Operation Instruction  
FINE TUNING  
Select to enter the submenu of TV. Then  
press ''Up /Down'' key on the remote control  
F I N E T U N I N G  
5 5 . 2 5 MHZ  
or ''CH+/ CH-'' on the front panel to select ''FINE TUNING''. Press ''Right'' key on the  
remote control to enter submenu of ''FINE TUNING''. Press ''Left/Right'' key on the  
remote control to adjust from low frequency or high frequency.  
CHANNEL EDIT  
Select  
to enter the submenu of TV. Then  
0 0 1  
0 0 2  
0 0 3  
0 0 4  
0 0 5  
0 0 6  
0 0 7  
0 0 8  
0 0 9  
0 1 0  
0 1 1  
0 1 2  
0 1 3  
0 1 4  
0 1 5  
0 1 6  
0 1 7  
0 1 8  
0 1 9  
0 2 0  
0 2 1  
0 2 2  
0 2 3  
0 2 4  
0 2 5  
0 2 6  
0 2 7  
0 2 8  
0 2 9  
0 3 0  
press ''Up/Down'' key on the remote control  
or ''CH+/CH-'' on the front panel to select  
''CHANNEL EDIT''. Press ''Right'' key on the  
remote control to enter submenu of  
''CHANNEL EDIT'' (Press program list key on  
the remote control to enter submenu of  
''CHANNEL EDIT'').  
1 NAME 2 DELETE  
3 SWAP  
MENU EXIT  
NAME: Press ''Cursor'' key on the remote control to select channel. Press ''1'' key on  
the remote control to name. Press ''UP/Down'' key on the remote Control to select  
letter or number. Press ''Left/Right '' key on the remote control to move digit and then  
press ''UP/Down'' key on the remote control to select letter or number. Press ''1'' key  
on the remote control to confirm.  
DELETE: Press ''Cursor'' key on the remote control to select channel which you wish  
delete. Press ''2'' key on the remote control, and then press ''1'' to confirm.  
SWAP: Press ''Cursor'' key on the remote control to select channel which you wish  
change name's position, press ''3'' key on the remote control, then press ''UP/Down''  
key on the remote control to select channel, press ''1'' to confirm.  
Select Channels with "CH+/CH-" Key  
Press Program key on the remote control or "CH+/ CH-" key on the front panel to  
select the channels.  
Select channels with the Return key you can go to the last channel when pressing  
the Return key. For example, if the last channel is 10 and the current channel is 20,  
you will go to channel 10 when pressing the Return key. You can switch the two  
favourite channels as you like.  
Download from Www.Somanuals.co2m0. All Manuals Search And Download.  
Basic Operation Instruction  
Select Channels with Numeric Keys  
1. Operations to select channels with 1 digit (0-9):  
Press the number keys (0-9)on the remote control to select TV channel directly.  
2. Operations to select channels with 2 digits (10-99):  
Press the number keys with 2 digits (10-99) on the remote control to select TV  
channels.  
3. Operations to select channels with 3 digits (100-199):  
Press the number keys with 3 digits (100-199) on the remote control to select TV  
channels.  
Note: With the mode of AV1, AV2, S-VIDEO1, S-VIDEO2, YPBPR, HDMI1,  
HDMI2, PC all functions and adjustments are similar with TV. User can  
check it at convenience. HDMI connector can realize DVI connector  
function with external HDMI/DVI commutator.  
USB signal source operation  
please insert USB memory card into USB interface of TV, press "source" key on the  
remote control or front panel to select USB signal source (if you don't insert the USB  
memory card into USB interface of TV, operation is invalid), press "OK" key to enter.  
Notice: This USB interface only support move U dish, can't connect move hard drive,  
also can't connect to USB interface of computer. USB support file format with Mp3/  
JPG. It isn't compatible with some of move U dishes, please replace move U dish.  
Download from Www.Somanuals.co2m1. All Manuals Search And Download.  
Simple Troubleshooting  
Symptom  
Factor  
Solution  
1.Antenna cable connector is loose,  
cable is damaged.  
2.Channel setting is incorrect.  
3.Antenna cable type is not matching.  
4.Direction or position of antenna  
cable is incorrect.  
1.Check the antenna cable connector plug whether or  
not loose, cable whether or not perfect.  
2.Refer to channel setting method, resetting again.  
3.Check antenna cable type(VHF/UHF)  
4.Adjust direction or position of antenna cable .  
5.Attempt to use signal amplifier.  
Snowflake speckle and  
sound noise.  
5.Signal is weak.  
TV image isbetter, buthas  
noise.  
TV system settingis incorrect.  
Enter to "TV"menu, reset soundsystem again .  
1.Check powercord whether ornot connect well.  
2.Check if " " on thefront panel ison.  
3.Press "power"on the remotecontrol.  
Power plug isloose, power  
cord don't connectwell.  
No image. No sound.  
TV image havestripe.  
Signal is exposedto disturb,  
such as car, neon light,  
electric blower etc.  
Don't use electric blower around machine, adjust  
antenna cable direction to reduce disturb.  
1.TV signalis reflected byvalley  
or building.  
2.Towarddirection of antenna  
cable is incorrect.  
1.Use high directionalantenna cable. UseFINE  
TUNING of "TV".  
2.Adjust toward directionof antenna cable.  
TV image haveshadow.  
No color.  
1.Color saturation is too low.  
2.Color system is incorrect .  
1.Enter "PICTURE"to add upcolor saturation.  
2.Enter "TV" tochange color system.  
1.Adjust volumeto proper value.  
2.Press "MUTE"button on remotecontrol to  
eliminate mute.  
1.Volumesetting is toolow.  
2.Sound ismuted.  
3.Sound system isincorrect.  
TV no sound.  
3.Enter "TV" tochange sound system.  
Computer no display, and  
prompt no signal input, red Signal cable is loose or fall off.  
indicator LED twinkling.  
Check signal cable whether or not loose, fall off,  
reconnect well again.  
1.Receive window of remote  
1.Remove objects, avoiding cover the receive  
window of remote control.  
2.Change battery.  
continue was covered by  
Remote control distance is  
objects.  
short, lose control.  
2.The battery energy of remote  
control is to low.  
1.Adjustment is incorrect.  
Computer display faintly.  
1.Use auto-adjustment function.  
2.Use commend mode.  
2.Display mode is incorrect.  
1.Use auto-adjustment function.  
2.Enter "GEOMETRY" to adjust horizontal or  
vertical position.  
Computer display image  
1.Adjustment is incorrect.  
excursion, not full screen,  
2.Display mode is incorrect.  
over screen.  
3.Use recommended mode.  
Noise Signals at turning off. Electrical release at turning off.  
Exterior influence, forexample  
It is normal.  
Press " "button on thefront panel toturn off  
electrical source, thenpress " "button to turn  
on the TV again after1-2 minutes.  
lightning, static electricityand so  
Can not operatethis  
on, which arepossibly to disturb  
machine.  
the normal operationof this  
machine.  
CAUTION: Don't let your machine display the same picture for a long time, please set up a screen protection  
procedure. If a high contrast picture remains for along time, this picture will bring a 'leave shadow' in screen.  
Usually the 'leave shadow' will disappear gradually when you turn off the machine power. However, this trouble  
can't be repaired, Which isn't in range of warranty.  
22  
 

Graco Crib 9045 User Manual
Grizzly Switch H8242 User Manual
Haier Washer XPB70 111S User Manual
Harbor Freight Tools Automobile Parts 36468 User Manual
Harbor Freight Tools Paint Sprayer 66222 User Manual
Hasbro Games 18663 Asst User Manual
Honeywell Laptop 99EXL0X XXXXXXXI User Manual
HP Hewlett Packard Server 704941 001 User Manual
Husqvarna Chainsaw 1153183 26 User Manual
IBM Network Card ARTIC960RxD User Manual