91090
91091
WHITE PAINTED VARNISHED
ADIRONDACK ADIRONDACK
CHAIR
CHAIR
ASSEMBLY AND OPERATING INSTRUCTIONS
91091 Pictured
3491 Mission Oaks Blvd., Camarillo, CA 93011
©
®
Copyright 2004 by Harbor FreightTools . All rights reserved.
No portion of this manual or any artwork contained herein may be
reproduced in any shape or form without the express written consent
of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353
8. Use eye and ear protection. Always wear ANSI approved impact safety
goggles during assembly.Wear a full face shield if you are producing wood
chips.Wear an ANSI approved dust mask or respirator when working around
wood, and chemical dusts and mists.
9. Take caution as some woods contain preservatives such as copper
chromium arsenate (CCA) which can be toxic. When cutting these
materials extra care should be taken to avoid inhalation and minimize skin
contact.
10. Check for damaged parts. Before using this chair, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Any part that is damaged should be properly
repaired or replaced.
11. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this item. Approved accessories are
available from Harbor FreightTools.
12. Do not assemble this chair if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or reflexes
are impaired while taking drugs. If there is any doubt, do not proceed with
assembly.
13. Maintenance. For your safety, service and maintenance should be performed
regularly. Check the alignment of all parts, and check the tightness of all
fasteners.
Warning: The warnings, cautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and situations
that may occur. It must be understood by the operator that common
sense and caution are factors which cannot be built into this product,
but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included.
1 Back
1 Front Support
1 Seat
14 Wood Screws
2 Front Legs
2 Back Supports
2 Arms
10 55mm Bolts with nut and washer
2 65mm Bolts with nut and washer
1 Owner’s Manual
If any parts are missing or broken, please call Harbor FreightTools at the number
on the cover of this manual, or contact your local Harbor Freight retailer.
SKU 91090-9D1o0w9n1load from Www.SomanuPalsa.cgoem3. All Manuals Search And Download.
Assembly
Carefully unpack the parts and check for damaged or missing parts.
1. Attach Left Front Leg (C1) and Right Front Leg (C2) to Seat (B) using 3 Bolts
(H) per side. Use the included washers and nuts to tighten.
2. Attach both Back Supports (D) to the inner sides of the Seat (B) using 2 Bolts
(H) per side. Tighten using the included washers and nuts.
3. Attach the Left Arm (E1) and Right Arm (E2) to the Front Legs (C1, C2) using
2 Wood Screws (G) per side. Attach the Arms (E1, E2) to the Back Supports
(D) using 1 Long Bolt (I) per side. Tighten the bolts using included washers
and nuts.
4. Attach the Back (A) to Seat (B) and Back Supports (D) using a total of 6
Wood Screws (G).
5. Attach the Front Support (F) to the Front Legs (C1, C2) using 2 Wood Screws
(G) per side.
6. Recheck the alignment of all parts, and recheck the tightness of all fasteners.
7. Set up the chair on a flat, level location. Do not exceed load capacity of 250 lbs.
Maintenance
1. This chair is made of natural Fir wood. This beautiful material will naturally
weather over time, especially if used outdoors.You can manage the speed
and extent of this weathering by controlling the environment in which the chair
is used and stored, as well as any coatings you may apply.
2. Leaving the chair outside exposed to weather, especially direct sun, rain and
salt air, will speed the weathering process.This can be slowed by removing
the chair from these conditions, or covering it with a suitable cover.
3. You may wish to stain, varnish or paint the chair. If so, follow the instructions
supplied with these coatings.
4. Occasionally wash the chair with a garden hose or pressure sprayer to remove
accumulated dust or dirt. Wipe down or blow off any remaining water left on
the chair after washing.
5. Periodically (perhaps once per year), recheck the tightness of all fasteners.
Normal usage of the chair and weathering of the wood may cause fasteners to
loosen.
SKU 91090-9D1o0w9n1load from Www.SomanuPalsa.cgoem4. All Manuals Search And Download.
Assembly Drawings
SKU 91090-9D1o0w9n1load from Www.SomanuPalsa.cgoem5. All Manuals Search And Download.
Parts List
Back
Seat
Left Front Leg
Right Front Leg
Back Support
Left Arm
Right Arm
Front Support
Wood Screws
55mm Bolt
65mm Bolt
with Washer and Nut
with Washer and Nut
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 91090-9D1o0w9n1load from Www.SomanuPalsa.cgoem6. All Manuals Search And Download.
|